C92200 Leaded Tin Bronze "Navy M"
C92200 (also known as C922) Bronze is well known for its industrial applications.
Pipe
Typical Uses for C92200 Leaded Tin Bronze "Navy M"
- Architecture: Ornamental Castings
- Building: Cooling Equipment, Heating Equipment
- Industrial: Fittings Used to 550 F, Gears, Bushings, Bearings, Pump Impellers, Pumps Used to 550 F, Cryogenic Valves, Valves for Water Meters, Medium Pressure Hydraulic Equipment, Piston Rings, Valve Components
- Fasteners: Nuts
- Marine: Marine Castings
- Plumbing: Medium Pressure Steam Equipment to 550 F
Product Specifications
| End Product | Specification |
| Centrifugal | ASTM B271, SAE J462, J461 |
| Continuous | ASTM B505, SAE J461, J462 |
| Fittings | ASME B16.24, SB61, ASTM B61, FEDERAL WW-P-460 |
| Flanges | ASME SB61, ASTM B61, FEDERAL WW-P-460 |
| Ingot | ASTM B30 |
| Sand | ASME SB61, SB584, ASTM B61, B584, SAE J461, J462 |
| Valves | MILITARY MIL-V-17547 |
Chemical Composition
| Al | Sb | Cu | Fe | Pb | Ni | P | Si | S | Sn | Zn | |
| Min/Max | 0.005 | 0.25 | 86.0 - 90.0 | 0.25 | 1.0 - 2.0 | 1 | 0.05 | 0.005 | 0.05 | 5.5 - 6.5 | 3.0 - 5.0 |
| Nominals | - | - | 88.0000 | - | 1.5000 | - | - | - | - | 6.0000 | 4.5000 |
Temper
| Product Type | Temper Type |
| Centrifugal | ASTM B271, SAE J462, J461 |
| Continuous | ASTM B505, SAE J461, J462 |
| Fittings | ASME B16.24, SB61, ASTM B61, FEDERAL WW-P-460 |
| Flanges | ASME SB61, ASTM B61, FEDERAL WW-P-460 |
| Ingot | ASTM B30 |
| Sand | ASME SB61, SB584, ASTM B61, B584, SAE J461, J462 |
| Valves | MILITARY MIL-V-17547 |
Mechanical Properties
| Temper | Sect. Size | Cold Work | Type Min | Temp | Tensile Strength | YS 0.05% UL |
YS 0.02% Offset |
YS 0.005% Offset |
Elong. | RH B |
RH C |
RH F |
RH 30T |
VH 500 |
BH 500 |
BH 3000 |
Shear Strgth |
Fatigue Strgth |
Izod Impact Strgth |
| - | in. | % | - | F | ksi | ksi | ksi | ksi | % | B | C | F | 30T | 500 | 500 | 3000 | ksi | ksi | ft-lb |
| - | mm. | - | - | C | MPa | MPa | MPa | MPa | - | - | - | - | - | - | - | - | MPa | MPa | J |
| As Centrifugal Cast | |||||||||||||||||||
| M02 | 68 | 34 | 16 | - | - | - | - | - | - | - | - | - | - | - | - | ||||
| M02 | 0 | SMIN | 20 | 234 | 110 | - | - | 22 | - | - | - | - | - | - | - | - | - | 0 | |
| As Continous Cast | |||||||||||||||||||
| M07 | 68 | 38 | 19 | - | - | - | - | - | - | - | - | - | - | - | - | ||||
| M07 | 0 | SMIN | 20 | 262 | 131 | - | - | 18 | - | - | - | - | - | - | - | - | - | 0 | |
| As Permanent Mold Cast | |||||||||||||||||||
| M05 | 68 | 34 | 16 | - | - | - | - | - | - | - | - | - | - | - | - | ||||
| M05 | 0 | SMIN | 20 | 234 | 110 | - | - | 24 | - | - | - | - | - | - | - | - | - | 0 | |
| As Sand Cast | |||||||||||||||||||
| M01 | 68 | 34 | 16 | - | - | - | - | - | - | - | - | - | - | - | - | ||||
| M01 | 0 | SMIN | 20 | 234 | 110 | - | - | 22 | - | - | - | - | - | - | - | - | - | 0 | |
| M01 | 68 | 40 | 20 | - | - | - | - | - | - | - | - | - | - | - | 11 | ||||
| M01 | 0 | TYP | 20 | 276 | 138 | - | - | 30 | - | - | - | - | - | 65 | - | - | 76 | 0 |
Physical Properties
| Product Property | US Customary | Metric |
| Coefficient of Thermal Expansion | 10.0 · 10-6 per oF (68-572 F) | 18.0 · 10-6 per oC (20-200 C) |
| Density | 0.312 lb/in3 at 68 F | 8.64 gm/cm3 @ 20 C |
| Electrical Conductivity | 14 %IACS @ 68 F | 0.083 MegaSiemens/cm @ 20 C |
| Electrical Resistivity | 72.5 ohms-cmil/ft @ 68 F | 12.00 microhm-cm @ 20 C |
| Incipient Melting | 600 oF | 315 C |
| Magnetic Permeability | 1 | 1 |
| Melting Point - Liquidus | 1810 F | 988 C |
| Melting Point - Solidus | 1518 F | 826 C |
| Modulas of Elasticity in Tension | 14000 ksi | 96500 MPa |
| Specific Gravity | 8.64 | 8.64 |
| Specific Heat Capacity | 0.09 Btu/lb/oF at 68 F | 377.1 J/kg · oK at 293 K |
| Thermal Conductivity | 40.2 Btu · ft/(hr · ft2 · oF) at 68F | 69.6 W/m · oK at 20 C |
Fabrication
| Joining Technique | Suitability |
| Brazing | Excellent |
| Coated Metal Arc Welding | Not Recommended |
| Gas Shielded Arc Welding | Not Recommended |
| Machinability Rating | 42 |
| Oxyacetylene Welding | Not Recommended |
| Soldering | Excellent |
Our Services
40+ years of experience
Aviva Metals Houston warehouse operation is a AS9120B, and AS9100D in our Ohio foundry, based on ISO 9001:2015. We are now also offering our complete range of brass, bronze and copper alloys in precision machined or milled parts, in full accordance with your drawings. Aviva Metals creates custom precision bearings and bushings, flanges, washers, double flange bearings, full half bearings, spacers and special machined parts that can be shipped on a global basis and in full accordance with most international standards.
